Professional bicycle spokes and motorcycles spokes nipples machine manufacture and supplier

Whatsapp: 0086-18637275223   Email: [email protected]

https://www.spokemaker.com/     Skype: romiter2000

Blogs

Life hacks: Five tips to save the bike mechanic time

The cycle workshop can be a hectic place at times (or all the time if you’re lucky!). The spirit of this piece is to show some of the things technicians may do in order to increase the accuracy and speed of repairs and therefore the productivity of the workshop, so when we say ‘hack’ we mean it in the professional sense. Here are my five top ‘hacks’ to make your workshop life that little bit easier:

1The internal spoke nipple trick

The-internal-spoke-nipple-trick

Dropping a spoke nipple into the internal walls of the rim is one of the most frustrating things you can do – especially on a deep section carbon wheel. This can be avoided by creating your own spoke nipple holder. All you’ll need is an old spoke (with a decent thread) and a spoke nipple. Put the spoke nipple onto the spoke the wrong way round and tighten it to the end of the threads (clamping the spoke in a vice and tightening the nipple with a spoke key is a good idea) This will leave you with about 3mm of thread showing from the end of the spoke – which you can use to screw the nipple you intend to use onto. The nipple is then secured in place allowing you to thread it hassle free through the rim and onto the spoke. No more rattling wheels!

The tubeless seating trick

Set-V-brakes-to-feel-the-same-EVERY-time

If you can, remove the valve core from the valve. Doing so will allow a greater volume of air to flow in from the track pump, really useful if you don’t have a compressor and are trying to frantically pump the air in using a standard track pump. Install the tubeless tyre onto the rim and lubricate between the bead of the tyre and the rim hook with soapy water. You can use sealant and I personally find this gives an additional seal, but you will need to scrub the sealant from the tyre bead and rim hook the next time you remove the tyre. Lubricating the tyre and rim stops the rubber from sticking and allows it to slip into place at much lower pressures. The tyre should seat around the 20 PSI mark.

 

This one is a simple one but if every mechanic does this in the workshop then all V-braked bikes will leave the workshop feeling the same and the customer won’t struggle to undo them. Unclip the centering springs and place the noodle so that the very end rests on the tip of the cradle. Pull the cable tight so that the pads stop the wheel from turning and secure the cable fixing bolt. Push the noodle down so that it rests correctly in the cradle. This trick works because it presets exactly the same distance every time.

SRAM brakes – just the lever

SRAM-brakes-–-just-the-lever

Now if you try this and the fluid that comes out of the lever is severely discoloured then you have no option but to flush the system and do a full bleed. Sorry.

BUT – for those people who stay on top of the service intervals (i.e every six months, not years) then this is a good trick to halve the time it takes to do a SRAM brake bleed as you are only going to bleed the lever not the full system. This works because air rises, so the theory is that most of the air will accumulate in the lever making it easier to remove.

The-bolt-through-truing-stand-trick

Take out the wheel and pad, put a bleed block in and remember to de-gas the fluid in the syringe thoroughly first and that the lever reach is set out far enough to give a good volume inside the lever body. Press down on the syringe and hold the pressure on (gently!) then flick the tip of the lever (pressing it in and allowing it to slip off the end of your finger is the best way). This shocks any air out that may be hiding in the lever body. Then pull up on the syringe to suck those bubbles out of the lever.

 

The bolt through truing stand trick stand

 

Now there is a dedicated adaptor for mounting bolt through axles into a truing stand but we’ve had good luck with the humble Hex key. A 10mm Hex key slid through the bolt through axle and then lowered into the truing stand is a quick, hassle free way to secure the wheel into a truing stand (if you don’t have the adaptors).

 

 

Company Profile

Romiter Group is a market leading designer and a manufacturer of bicycle spokes and motorcycle spokes making machine, which wins wide reputation for products with high efficiency, excellent reliability, easy maintenance and long lifespan.

We provides a complete bicycle and motorcycle spokes and nipple making solution, which includes Bicycle Spokes Making MachineBicycle Spokes Nipple Making Machine, High Speed Motorcycle Spokes Making MachineMotorcycle Spokes Nipple Making MachineButted Spokes Making Machine, Bladed Spokes Making Machine, Wire Straightening Cutting Machine MachineWire Rivet Making Machine, Cycle Spoke Nipples Packing Machine, Ellipse-shaped Spoke Making Machine, Cycle Rim Making Machine etc.

    Send Us Inquiry to Get Quotation

    Please enter your contact information and the details you want to know about our product.

    Your Name (required)

    Your Email (required)

    Country

    WhatsApp/Phone Number

    Skype

    Subject

    Your Message (required)

    Tags:
    Prev:
    Next:
    X

    Online Chat

    Spoke and Nipple Making Machine Supplier Skype Spoke and Nipple Making Machine Supplier Email Spoke and Nipple Making Machine Supplier Telegram Spoke and Nipple Making Machine Supplier Wechat Spoke and Nipple Making Machine Supplier Wechat